CRIUS ALL IN ONE PRO Flight Controller v2.0

1,590.00 ฿

ค่าจัดส่ง ยังไม่รวมค่าจัดส่ง

จำนวน :

รายละเอียดสินค้า

บอร์ดคอนโทรลอีกตัวหนึ่งของ CRIUS ที่รู้จักกันในนาม MultiWii ได้ออกรุ่นใหม่ล่าสุดที่มีคุณสมบัติเทียบเท่า APM ของค่าย Ardupilot เลยทีเดียว ความสามารถของบอร์ดลง Firmware ได้ทั้ง 2 ค่ายคือ Multiwii และ Audupilot (APM) ในราคาสุดคุ้ม ลงผ่าน Arduino หรือ Mission planner แก้ไข/ปรับแต่ง/เพิ่มเติม Software เองได้ตามแบบฉบับ MultiWii ค่ะ

Video:

http://www.youtube.com/watch?v=Emf7WAa0YcY&sns=em

http://vimeo.com/47677259

http://www.youtube.com/watch?v=OkkoudNBIQc

ทดสอบ บอร์ด AIOP V2.0 ลง Firmware Version 2.3 และเปิดใช้โปรแกรม MultiWii GUI 2.3 ได้แน่นอน

Hardware Features:

·Supported MegaPirateNG /ArduCopterNG/ArduPlaneNG/MultiWii firmware

·8-axis motor output and 3 servos output for gimbal system

·8 input channels for standard receiver and PPM SUM input channel

·4 serial ports for debug/Bluetooth/OSD/GPS/telemetry module

·8 Analog port for Airspeed Sensor/Current & Voltage Sensor/LED controller

·User-defined pads D32~37 & PG1~PG5

·I2C 5V port for external device

·Output/USB ports provided over current protection

·Reverse polarity protection for input power

·Select jumper for choose internal or external magnetometer

·Onboard 16Mbit Dataflash chip for automatic datalogging

·ATMega 2560-16AU Microcontroller

·MPU6050 6-axis gyro/accel with Motion Processing Unit

·HMC5883L 3-axis digital magnetometer

·MS5611-01BA03 highprecision altimeter with metal cap

·FT232RQ USB-UART chip and Micro USB receptacle for uploading firmware and debug

·PCA9306DP1 logic level converter for I2C

·Match the standard of RoHS

Input power selection

·One of the following way

- Connect 5V power cable from ESC or UBEC to ESC/Servo port, the J1 jumper must be closed.

- Connect 5V power cable to the external power port, the J1 jumper must be removed.

Other

·Dimension: 50mmX50mmX11.6mm

·Weight: 14.5g

·Fixing hole spacing: 45mm

·Hole diameter: 3.1mm

Package content

·ALL IN ONE PRO Flight Controller x 1

·3Pin to 1Pinx3 cable 100mm x 3

·3Pin to 3Pin cable 100mm x 1

·Molex 1.25mm 4Pin cable 100mm x1

·Molex 1.25mm 6Pin cable 100mm x1

·Molex 1.25mm 8Pin cable 100mm x2

All IN One Pro Board Setup with MegaPirates COde

The MegaPirates NG Code focuses on porting the Arducopter code over to various other controller boards, including the All in one Pro board that we sell.

This guide will show you how to configure and setup your AIOP board to work with the MegaPirates NG code. The nice thing with the MegaPirates code is that it can be used with the ArduPilot Mission Planner - A graphical user interface for your autopilot

The AIOP board can also run multiwii code if you want.

Buy AIOP Board

All in One Pro Board Layout

All in one pro V2 Top Layout - click for larger image

All In One Pro v2 Bottom View

Getting the MegaPirates Software/Tools

Download the latest version of the MegaPirates NG code from GitHub here
The newest version will be on the top

The Arduino software is used to configure and compile the MegaPirateNG Code and upload it to your Crius AIOP Board. You can download it from here
Create a directory on your PC called Crius (on your desktop will be fine)
Inside the Crius directory create two more directories, Arduino and MegaPirate
Unzip the MegaPirateNG files into the MegaPirate Directory you created
Unzip the Arduino files into the Arduino Directory you created.
Now open the MegaPirate Folder and copy the Libraries folder to the Arduino Folder (you will be prompted and asked if you wanted to merge the two directories and overwrite any files etc).
Open the Arduino Application inside the arduino folder (arduino.exe)

ArduPilot Mega Mission Planner Software

APM Planner was written for APM and as such not all features work on the Crius AIO with MegaPirateNG. For example you cannot upload firmware using this tool. The APM Planner is used for configuring and calibrating your AIOP board
You will need to download the APM Planner software from here
For more details on the features of this software go to the wiki here

Setting Up Arduino

First Plug in your AIOP board, windows 7 should automaticaly load the correct drivers.
Under tools check that its is configured for the correct board, for the Crius is should be Arduino Mega 2560 or Mega ADk as shown
Now select the serial port the Crius AIO. This is done in Tools>Serial Port in the menu. It is usualy the biggest COM port number

CONFIGURING and Uploading the MegaPirate Code

Use File > Open in Arduino and navigate to the Megapirate folder your created, open the sub folder called ArduCopter. Inside this folder there is a file called ArduCopter.pde. open this file.

A new window will open showing the megapirate code.
You will notice that there are tab's along the top the only one that we have to make changes to is theAPM_Config.h and as you can see buy the picture above that this is the second tab along just click on this to edit it.

Browse through the code to change the following sections
First one is the Board Type, it should be changed to:
#define PIRATES_SENSOR_BOARD PIRATES_CRIUS_AIO_PRO_V2
Change the Baro to
#define CONFIG_BARO AP_BARO_MS5611_I2C

Change the GPS Protocol to
#define GPS_PROTOCOL GPS_PROTOCOL_AUTO
If you are using the Extend board, you should change this to UBLOX.
If you find that the AUTO detection is not working, you may need to choose a specific option.

Change the Frame type depending on your multicopter configuration
#define FRAME_CONFIG QUAD_FRAME
You will also need to set your frame orientation
#define FRAME_ORIENTATION X_FRAME

Click the Verify and Upload button on the toolbar to compile and load the code onto your AIOP board.
You should not get any errors, if you do go back to the beginning and start again. It is known to get errors if you have not copied the libraries folder from MegaPirate into the Arduino folder…… so if in doubt redo it.
Once you have successfully compiled and uploaded MegaPirateNG to your Crius Board you can now move onto installing APM Planner, checking the board and setting up your radio and calibration etc.
If you are using extra hardware like a telemetry kit, you will need to change some other settings (see below)

AIOP Megapirates Status LEDS

Connecting your GPS module

Picture Credit - Gaza07 @multi-rotor.co.uk

An easier way to connect your AIOP GPS module and Telemetry module is with a special harness that we sell, so you dont need to cut/solder any wires.

Buy AIOP Harness

Picture Credit - fpvcentral.net

Almost any serial GPS module can be used with the AIOP board. However we suggest you use the Ublox NEO 6M GPS module.
You can also use the Ublox LEA 6H GPS module
The GPS needs to be connected to the RX2 and TX2 ports on the Crius AIO controller.
At the same time, 5V power has to be supplied as well, but the serial ports 1, 2 and 3 on that connector don’t offer Vcc (they can if you power the board externally and remove the yellow jumper, but that’s for another tutorial) – so the easiest way is to just use the 5V and GND pins of the I2C port.
This is simple because Crius was so nice to supply all the molex connectors needed with the board – all you have to do is switch around the pins a bit.

Configuring your GPS Module - Optional
(Ublox NEo/LEA units) -

There is a config file that you can use with pre-defined settings for use with the ardupirates code.
You will first need to download and install U-center to confugre your Ublox module - Download Here
You will also need to download the config file Here - (right clock and save as)

Now you will need to connect your GPS module to your computer via USB/FTDI depending on your GPS module.
Once connected open U-Center

To load the GPS config file click on the Tools>GPS Configuration menu as shown

A window will open asking you to choose a config file
Open the config file you downloaded before and send the file to the GPS module

You might get an error if you are using a NEO GPS module, but this can be ignored.
Click on Yes to continue.
You might get a couple of errors, but once it it complete the important settings will be saved onto the GPS module. You should now be able to connect to it via U-Center at the baud rate of 38400.
You have now configured the module with optimum settings for the ArduPirate code

If you have any questions about setting up your All in one pro board, or any other general multirotor questions be sure to visit our forums to talk to other members!